Stag Power Rentals supplies diesel industrial generators from 20kW to 2,000kW, dispatched from our Dickinson, TX location with shipping available nationwide. Our fleet is diesel-only, and every unit is sized to a facility’s actual running and starting loads rather than a stock capacity guess, with load-bank testing available before a generator leaves the yard.
Sulphur sits on I-10 between Vinton and Westlake, about 20 miles east of the Texas line, inside Calcasieu Parish, one of the densest petrochemical manufacturing corridors on the Gulf Coast. A scheduled turnaround or unit outage at a nearby plant calls for different power planning than storm-season standby for a Sulphur office, warehouse, or municipal building, and we size each rental to the job rather than a one-size-fits-all package. Review our hurricane contingency power plan, call 1-844-STAG-PWR, or request a quote to start sizing your Sulphur rental.
Questions? Call 1-844-STAG-PWR
Call Our Team: 1-844-STAG-PWR
Looking for a 20kW-2000kW Generator Near You?
Whether you are planning for an outage or have an emergency situation, we’re ready 24/7 to ship a generator that will meet your power requirements.
Sulphur’s petrochemical turnaround schedule and Gulf storm exposure drive the same generator demand we see across our home Gulf Coast market. Stag Power Rentals ships the same diesel-only, load-bank-tested fleet from 20kW to 2,000kW to Calcasieu Parish that we deploy nationwide, roughly 137 miles and 2 hours 15 minutes from our Dickinson, TX yard via I-10, sizing each unit to actual running and starting loads for plant turnarounds, commercial buildings, and municipal facilities. Cable, panels, and transfer switches ship alongside the generator, and our team coordinates site access for gated industrial sites. Confirm current availability and lead time for your Sulphur location.
20kW-2000kW • Portable • Trailer • Skid • Diesel Generators
Stag Power Rentals provides diesel industrial and commercial generators from 20kW to 2,000kW for rental across Sulphur and the surrounding Calcasieu Parish area. Every unit in our fleet runs on diesel only, and we ship and deliver nationwide from our Dickinson, TX dispatch point.
We work with facility managers, contractors, and plant operators to size generators to the true electrical load of the job, whether that’s temporary power ahead of permanent utility service, standby power for a storm, or bridge power during a plant maintenance window.
Sulphur grew up as a company town around sulfur mining and, later, oil refining; the Cities Service (Citgo) refinery arrived in 1943, and the area is still largely dependent on oil refineries and petrochemical plants for employment. That legacy puts Sulphur inside the same industrial corridor as the Sasol Lake Charles Chemical Complex in neighboring Westlake, and plant turnarounds, unit outages, and maintenance windows in that corridor routinely require temporary power for compressors, pumps, blowers, control rooms, and site lighting while permanent supply is offline. A generator sized to the startup current of large motors, not just their running load, keeps a turnaround schedule from slipping.
Sulphur carries a separate risk on top of that industrial base: named storms moving off the Gulf. Hurricane Laura made landfall in Calcasieu Parish in August 2020 as one of the strongest storms on record to hit Louisiana, and Hurricane Delta followed the same track about six weeks later. Homes, commercial buildings, and municipal facilities across the parish went without utility power for extended stretches during that run, which is why standby generator planning ahead of hurricane season is standard practice for Sulphur property managers rather than something arranged after a storm is already in the Gulf.
Sulphur sits directly on I-10 between the towns of Vinton and Westlake, with local access via exits 20, 21, and 23, and Lake Charles 9 miles to the east. That position puts it within easy reach of the Westlake petrochemical corridor, the Sasol complex, and the broader Calcasieu Ship Channel industrial base, while still functioning as its own city with retail, medical, and municipal facilities that need independent backup power planning.
The table below lines up common capacity ranges with typical Sulphur applications.
| Generator Size | Typical Load | Common Sulphur Use |
|---|---|---|
| 20-60 kW | Lighting, point-of-sale systems, small HVAC | Retail and local businesses along the I-10 corridor |
| 100-150 kW | Building HVAC, elevators, medical office equipment | Commercial property standby ahead of storm season |
| 300-400 kW | Conveyors, packaging lines, shop equipment | Warehouse and manufacturing sites supporting the petrochemical corridor |
| 600-800 kW | Compressor and pump motor starting loads | Plant turnaround support, distribution panel rental |
| 1000-1500 kW | Large process motors, multi-building loads | Extended outage coverage, see 1,500kW generator rentals |
| 2000 kW (paralleled) | Facility-wide critical load | Emergency response and disaster recovery after a named storm |
See our full generator size guide, including our 45kW, 150kW, and 300kW diesel generator pages, or view the complete industrial generator rental lineup.
| Factor | Why It Matters | Sulphur Consideration |
|---|---|---|
| Running vs. starting load | Motors draw several times their running amperage at startup | Compressor and pump motors common at nearby refineries and chemical plants |
| Voltage and phase | Must match facility service to connect safely | Confirmed before dispatch on every quote |
| Runtime and fuel tank size | Determines refueling frequency | Extended runs during turnarounds or multi-day storm outages |
| Site elevation and drainage | Equipment placement above expected water levels | Low-lying parcels near area drainage canals and the Calcasieu River basin |
We dispatch and ship nationwide from our Dickinson, TX location. The standard highway route runs east from Dickinson to Beaumont, Texas, then continues on I-10 across the Sabine River into Louisiana to Sulphur’s I-10 exits 20, 21, and 23. That route covers approximately 137 miles and runs roughly 2 hours and 15 minutes under normal traffic conditions.
Sites inside a refinery or chemical plant gate in the Westlake area typically require gate clearance, a safety orientation, and coordination with the site’s contractor of record before a generator and support equipment can be staged. Commercial and municipal sites are generally more straightforward, though we still confirm overhead clearance, ground conditions, and any storm-season road restrictions as part of the quote process rather than assuming a standard drop-off.
Diesel supply and technician access matter for both turnaround jobs and storm-standby rentals. We plan fuel tank sizing and servicing intervals around expected runtime, and can arrange technician support for startup, monitoring, and load-bank testing where the job calls for it.
Beyond the generator itself, most industrial jobs need supporting gear: cable runs sized to the distance from generator to load, transfer switches, and power distribution equipment such as a distribution panel to split load across multiple circuits or buildings. We include this equipment in the same quote as the generator so it arrives sized and tested together.
Our customers here span warehouse and manufacturing operations supporting the petrochemical corridor, commercial property managers preparing for storm season, and emergency response and disaster recovery work following a named storm. We also support municipalities and government facilities and local businesses that need backup power to stay open through a utility outage.
Sulphur is also 9 miles from Lake Charles, and we serve that market with the same fleet and dispatch point; see our Lake Charles, Louisiana generator rental page for details specific to that area.
To put together an accurate quote, we ask for: the equipment or building load you’re backing up, voltage and phase, expected rental duration, delivery address and site access notes, and whether the job needs distribution equipment or a technician on site. Call 1-844-STAG-PWR or request a quote to get started.
No. Stag Power Rentals’ fleet is diesel-only.
Diesel generators for storm-standby power are in the highest demand right before and during an active storm. Booking ahead of the season, or as soon as a storm is forecast toward the Gulf, gives us the most flexibility to size and stage your unit.
Yes. We size generators to the running and starting loads of process equipment such as compressors, pumps, and blowers, and can include distribution panels and cable to match a plant’s electrical layout.
Yes, with coordination. Sites with gate clearance, safety orientation, or contractor-of-record requirements should share those details when requesting a quote so we can plan delivery accordingly.
Sulphur is approximately 137 miles from our Dickinson, TX location via I-10, about a 2 hour and 15 minute drive under normal conditions. Delivery scheduling depends on the size of the unit and current fleet availability.
Many commercial buildings run on 100-150 kW units, though the right size depends on HVAC load, elevators, and any equipment that must stay powered. We size each rental to the building’s actual load.
Stag Power Rentals
2025 Nichols Ave
Dickinson, TX 77539
Industrial & Commercial Generator Rentals
1-844-STAG-PWR
If a hurricane has left your business without power call us. We can guide you through the generator rental process and help restore power to your business with as little downtime as possible.
If you want to get ahead of power outage, then signup for our Hurricane Contingency Plan >
