Stag Power Rentals supplies industrial and commercial generator rentals from 20kW to 2,000kW to businesses, contractors, and public agencies in Jennings, Louisiana and throughout Jefferson Davis Parish. Our fleet is diesel-only, built for the load demands of agricultural processing, oilfield-adjacent industry, and municipal operations that cannot tolerate an unplanned outage.
Jennings sits at the intersection of two industries that both depend on steady power: rice milling and processing, which runs on tight harvest-season schedules, and the oilfield services network that grew out of the parish’s history as the site of Louisiana’s first producing oil well in 1901. Both need generators sized correctly the first time, not a unit swapped out mid-project because it was undersized.
Every unit we deliver to Jennings ships from our Dickinson, Texas dispatch point with full logistics support, from load calculation through fuel planning. To get a sizing recommendation and pricing for your site, request an industrial generator rental quote and our team will confirm availability for your timeline.
Questions? Call 1-844-STAG-PWR
Call Our Team: 1-844-STAG-PWR
Looking for a 20kW-2000kW Generator Near You?
Whether you are planning for an outage or have an emergency situation, we’re ready 24/7 to ship a generator that will meet your power requirements.
Jennings’ economy runs on rice processing and Jefferson Davis Parish’s oilfield-service network, both of which depend on power sized from actual motor and equipment load data rather than generic estimates. Stag Power Rentals delivers the same diesel-only fleet we run across the Gulf Coast to Jennings, roughly 181 miles and 2 hours 45 minutes from our Dickinson, Texas dispatch point, covering everything from small commercial backup to full processing-facility loads. Confirm current availability and lead time for your Jennings location.
20kW-2000kW • Portable • Trailer • Skid • Diesel Generators
Stag Power Rentals supplies industrial and commercial diesel generators from 20kW to 2,000kW for rice processing, oilfield-service yards, and municipal facilities throughout Jennings, Louisiana and Jefferson Davis Parish. Generators are dispatched from our Dickinson, Texas yard and delivered nationwide, sized according to connected load, startup demand, voltage, phase, and site access.
Jennings’ rice milling and oilfield-service economy creates year-round demand for temporary power that can’t wait on a harvest or turnaround schedule. For immediate assistance, call 1-844-STAG-PWR or request an industrial generator rental quote.
Jennings is the parish seat of Jefferson Davis Parish, a role it has held since the parish was carved out of Calcasieu Parish in 1913. The city’s economy was built on two foundations: rice agriculture, brought in by Midwestern settlers recruited by agricultural promoter Seaman A. Knapp in the 1880s, and oil production, which began in the parish in 1901 when the Jules Clement farm produced Louisiana’s first commercial oil well. That discovery is why Jennings still carries the title “Cradle of Louisiana Oil,” and why the surrounding parish retains an active base of oilfield service, equipment, and support businesses alongside its agricultural operations.
Stag Power Rentals delivers industrial generator rentals from 20kW up to 2,000kW to support both sides of that economy, along with the commercial and municipal facilities that serve the Jennings community. Our fleet is diesel-only, sized and dispatched to match documented load requirements rather than a generic city-page recommendation.
Rice milling and drying facilities in and around Jennings operate on schedules set by the harvest, not by how quickly a utility can restore service after a storm or equipment failure. A dryer or mill that goes down mid-run risks spoiled product and missed delivery windows that can’t simply be pushed to next week. The same is true for grain elevators, cold storage tied to agricultural distribution, and irrigation pump stations that depend on continuous power during the growing season.
Rice dryers, elevator leg motors, and processing line equipment typically carry high starting loads relative to their running load, which means sizing has to account for motor inrush, not just steady-state draw. A facility running multiple large motors off one panel may need a larger unit than the nameplate total would suggest, particularly where equipment starts sequentially rather than staggered. We work from actual equipment specifications and panel data to confirm sizing before a unit is dispatched, rather than defaulting to a round-number recommendation.
Jefferson Davis Parish’s oilfield heritage left behind a network of service yards, equipment rental operations, and industrial support facilities that still require dependable temporary power for maintenance turnarounds, equipment testing, and short-term site power where permanent utility service isn’t practical. These facilities often need higher-capacity units than a typical retail or office tenant, and they need them available on short notice when a project timeline shifts.
The table below shows common facility types in the Jennings area matched to a typical generator size range. Exact sizing should always be confirmed against your equipment’s actual load data.
| Facility Type | Typical Load Profile | Recommended Generator Range |
|---|---|---|
| Small commercial or retail site | Lighting, HVAC, point-of-sale systems | 20kW – 60kW |
| Rice dryer or grain elevator | High motor inrush, sequential starts | 150kW – 300kW |
| Irrigation pump station | Continuous motor load during growing season | 60kW – 150kW |
| Oilfield service or equipment yard | Mixed shop equipment, welding, compressors | 150kW – 600kW |
| Food or agricultural processing plant | Refrigeration, processing line motors | 300kW – 800kW |
| Municipal or water treatment facility | Pumps, lift stations, treatment equipment | 150kW – 600kW |
| Large industrial or manufacturing site | Full-facility backup, heavy equipment | 800kW – 2,000kW |
See our full breakdown of specific unit classes, including the 150kW diesel generator, 300kW diesel generator, and 600kW diesel generator rental classes, or view the complete generator sizing guide.
Stag Power Rentals dispatches from 2025 Nichols Ave, Dickinson, TX 77539. The driving distance from our dispatch point to Jennings, Louisiana is approximately 181 miles, a drive of roughly 2 hours and 45 minutes under normal traffic conditions.
The route runs almost entirely along Interstate 10 East: from Dickinson, transport crosses into Houston, continues east through Beaumont and Orange, Texas, crosses into Louisiana near Vinton, and continues through Lake Charles before reaching the Jennings exit off I-10. Because the route is a single interstate corridor with no secondary-highway transfers required, transit time is predictable and consistent for scheduling delivery and pickup windows.
On arrival, our delivery team confirms site access, ground conditions, and panel location before positioning the unit, which matters for facilities set back from paved frontage roads common to rice farm and agricultural sites in the parish, as well as service yards with restricted equipment lay-down space.
In addition to agricultural and oilfield-adjacent facilities, we support a range of commercial and public-sector operations in the Jennings area, including warehouse and manufacturing facilities, municipal and government operations, and local businesses that need backup power during grid outages or planned maintenance. If your facility distributes power across multiple loads once a generator is on site, our power distribution equipment and distribution panel rentals can be delivered alongside the generator.
For businesses planning ahead of Gulf Coast storm season, review our hurricane contingency power plan to reserve generator capacity before a storm makes landfall rather than competing for availability afterward.
Stag Power Rentals also serves nearby Louisiana communities, including Lake Charles and Lake Arthur, both within Southwest Louisiana’s oil and agricultural corridor.
Is natural gas power available?
No. Stag Power Rentals’ fleet is diesel-only.
What generator sizes are available for rent in Jennings?
Our fleet ranges from 20kW to 2,000kW, covering everything from small commercial backup to full industrial and processing-facility loads.
How far is Jennings from your dispatch point?
Jennings is approximately 181 miles from our Dickinson, Texas dispatch point, roughly a 2 hour 45 minute drive via I-10 East.
Can you size a generator for a rice dryer or grain elevator?
Yes. We size units based on actual motor and equipment load data, including starting inrush, rather than nameplate totals alone.
Do you deliver to rural or farm sites outside city limits?
Yes. Our delivery team confirms site access and ground conditions ahead of delivery for sites off paved frontage roads.
How quickly can a generator be delivered to Jennings?
Delivery timing depends on unit size and current fleet availability. Request a quote for a delivery estimate tied to your specific equipment and timeline.
Stag Power Rentals
2025 Nichols Ave
Dickinson, TX 77539
Industrial & Commercial Generator Rentals
1-844-STAG-PWR
If a hurricane has left your business without power call us. We can guide you through the generator rental process and help restore power to your business with as little downtime as possible.
If you want to get ahead of power outage, then signup for our Hurricane Contingency Plan >
